B008F high Severity

B008F: Rollover Protection Disable Switch Circuit Fault (Airbag System)

Airbag/safety restraint system may be disabled or function incorrectly; vehicle may fail safety inspection.

Overview

DTC B008F refers to a fault in the rollover protection disable switch signal circuit within the Supplemental Restraint System (airbag), indicating a short to ground, short to voltage, or open/high resistance condition. This affects the airbag module’s ability to correctly read the switch status and can disable safety functions.

Common Symptoms

  • Airbag/SRS warning light illuminated on dashboard
  • Possible disablement of rollover protection or airbag circuits
  • Stored crash-related or safety restraint module faults

Most Common Causes

Short to ground in the rollover protection disable switch signal circuit high

Detected when signal circuit is grounded unexpectedly.

Open/high resistance in rollover protection disable switch circuit high

Indicates wiring break, poor contact, or switch failure.

Short to voltage on the rollover protection disable switch signal circuit medium

Power feed short could cause incorrect readings.

Faulty rollover protection disable switch component medium

Internal failure of the switch can trigger B008F.

Faulty Inflatable Restraint Sensing and Diagnostic Module (SDM) low

Module misinterpretation or internal fault may cause code.

Diagnostic Steps

  1. Perform initial safety and system check; ensure battery is properly connected and airbag system is powered.
    Expected: No unrelated codes; airbag system responds normally.
    Interpretation: Baseline system health confirmed.
  2. Visually inspect wiring and connectors at rollover protection disable switch and SDM for damage or corrosion.
    Expected: No frayed wires, corrosion, bent terminals.
    Interpretation: Damaged wiring can often cause circuit irregularities.
  3. Measure resistance across rollover protection disable switch terminals with switch open and closed.
    Expected: Resistance within specified range (e.g., 380–420 ohm open, 95–105 ohm closed per manufacturer spec).
    Interpretation: Values outside expected range indicate faulty switch.
  4. Check for shorts to ground or voltage on the signal circuit using a multimeter.
    Expected: No unexpected voltage at ground; signal circuit only has correct reference voltage when expected.
    Interpretation: Unexpected readings confirm wiring circuit faults.
  5. If wiring and switch test normal, test the SDM for proper signal interpretation and communication.
    Expected: SDM reports valid switch statuses without fault.
    Interpretation: Faulty SDM may need replacement if it misinterprets valid inputs.

Repair Solutions

Repair or replace damaged wiring/connectors related to rollover protection disable switch circuit medium
Estimated Cost: $50 - $200

Costs vary depending on repair extent; wiring harness repair is typically less costly than component replacement.

Replace rollover protection disable switch medium
Estimated Cost: $100 - $300

Component cost varies by vehicle; consult OEM for exact part.

Replace or reprogram the Inflatable Restraint Sensing and Diagnostic Module (SDM) if confirmed faulty hard
Estimated Cost: $400 - $1000

Airbag module replacement often requires professional service and may require reprogramming.

Common Misdiagnoses

Avoid these common diagnostic mistakes:

  • Generic body code indicating unrelated wiring issue due to misinterpretation of reserved B codes
  • Airbag crash sensor fault when the specific issue is rollover disable switch wiring

Frequently Asked Questions

What is the definition of the B008F engine code?

When your OBD-II scanner reads B008F, it means: Rollover Protection Disable Switch Circuit Fault (Airbag System). This code is related to the vehicle's Sensors.

Can B008F cause engine damage?

This is a high priority issue. Airbag/safety restraint system may be disabled or function incorrectly; vehicle may fail safety inspection.

What are the symptoms of B008F?

You may experience the following: Airbag/SRS warning light illuminated on dashboard, Possible disablement of rollover protection or airbag circuits, Stored crash-related or safety restraint module faults.

What causes the B008F code?

The most common causes are: Short to ground in the rollover protection disable switch signal circuit, Open/high resistance in rollover protection disable switch circuit, Short to voltage on the rollover protection disable switch signal circuit.

How much does it cost to fix B008F?

The cost varies significantly based on the root cause. For example, replacing a Repair or replace damaged wiring/connectors related to rollover protection disable switch circuit typically costs between $50 and $200, while fixing a Replace or reprogram the Inflatable Restraint Sensing and Diagnostic Module (SDM) if confirmed faulty can range from $400 to $1000.

Is the B008F code specific to Toyota?

B008F is not specific to any one brand. It can appear on Ford, Dodge, Toyota, Honda, Jeep, and other vehicles.

User Comments (0)

Share your experience or ask a question about this code.

Be the first to share your experience with B008F!