B0085 medium Severity

B0085: Second Row Right Seatbelt Load Limiter Deployment Control (Subfault)

May not immediately affect drivability but indicates a fault in supplemental restraint system which could compromise occupant safety in a collision.

Overview

Diagnostic Trouble Code B0085 relates to the second row right seatbelt load limiter deployment control subfault in the vehicle’s body restraint system; may indicate sensor or wiring issues.

Common Symptoms

  • Airbag/SRS warning light illuminated
  • Seatbelt warning indicator active or intermittent
  • Stored alongside related SRS/seatbelt codes

Most Common Causes

Faulty second row right seatbelt load limiter sensor medium

ISO/SAE definition identifies B0085 as related to the seatbelt load limiter control circuit which may fail or misreport status.

Wiring harness open, short, or poor continuity in sensor circuit medium

Forum and technical sources report wiring breaks in seat/door harness causing intermittent code triggers.

Poor electrical connection/corrosion at connectors medium

Connector corrosion and loose contacts reported in community discussions as causes.

Inflatable Restraint Sensing and Diagnostic Module fault low

Some generic sites mention SDM module issues though not confirmed by OEM references.

Diagnostic Steps

  1. Perform initial visual inspection of seatbelt load limiter wiring and connectors in second row right seating area.
    Expected: No damage, corrosion, or loose connector pins.
    Interpretation: If damage or corrosion is present then repair/clean before proceeding.
  2. Use a professional scan tool to read DTC B0085 and any associated codes; note freeze frame data.
    Expected: Consistent presence of B0085 across restarts.
    Interpretation: Confirms persistent fault rather than transient.
  3. Measure continuity and resistance of load limiter sensor circuit with a multimeter.
    Expected: Circuit within manufacturer spec resistance range.
    Interpretation: Out-of-range values suggest open/shorting in wiring or sensor failure.
  4. Inspect and service connectors—clean and secure seating of pins.
    Expected: Good contact and secured lock.
    Interpretation: Improvement or code clearance after this step indicates connector issue.
  5. If wiring and connectors check out, replace seatbelt load limiter sensor per vehicle-specific repair manual.
    Expected: Code does not return after replacement and system reset.
    Interpretation: Confirmed sensor failure.

Repair Solutions

Repair or replace damaged wiring harness/connectors medium
Estimated Cost: $50 - $250

Costs vary with extent of harness damage and labor rates.

Clean and secure electrical connectors in seatbelt sensor circuit easy
Estimated Cost: $10 - $50

Often resolves intermittent faults due to poor contact.

Replace second row right seatbelt load limiter sensor hard
Estimated Cost: $200 - $600

Part and labor cost can vary by vehicle; safety system repair should be done by qualified technician.

Common Misdiagnoses

Avoid these common diagnostic mistakes:

  • Generic 'airbag sensor fault' without specifying seatbelt load limiter component

Frequently Asked Questions

What is the definition of the B0085 engine code?

The B0085 code stands for Second Row Right Seatbelt Load Limiter Deployment Control (Subfault). This generally indicates an issue with the Sensors system.

Reflecting on severity: How bad is B0085?

The B0085 code is considered medium severity. May not immediately affect drivability but indicates a fault in supplemental restraint system which could compromise occupant safety in a collision.

What happens when the B0085 code is active?

Common symptoms include: Airbag/SRS warning light illuminated, Seatbelt warning indicator active or intermittent, Stored alongside related SRS/seatbelt codes. You might also notice the Check Engine Light is on.

Common triggers for the B0085 error

Potential culprits include: Faulty second row right seatbelt load limiter sensor, Wiring harness open, short, or poor continuity in sensor circuit, Poor electrical connection/corrosion at connectors. A proper diagnosis is recommended.

What is the price difference for fixing B0085?

Expect to pay around $50 if the issue is a Clean and secure electrical connectors in seatbelt sensor circuit, but up to $600 if the Replace second row right seatbelt load limiter sensor needs replacement.

What cars are affected by the B0085 code?

Yes, B0085 is a generic code that applies to all OBD-II compliant vehicles, including Ford, Toyota, Honda, Chevrolet, Nissan, Dodge, BMW, and more.

User Comments (0)

Share your experience or ask a question about this code.

Be the first to share your experience with B0085!